8-fold DI/DO (Digital Input/Output) 1-Wire switching module - 8A 230V - with push-button inputs

High power 8-fold DI/DO (Digital Input/Output) 1-Wire switching module - 16A 230V - with push-button inputs: With this 8-fold switching module, 8 DC or AC consumers can be switched via a 1-Wire interface using 8 push-buttons (external or on the module surface). This can be used to operate lighting, radiator valves or sockets, for example The module is designed for a load capacity of 10A per channel (16A for 3 seconds) continuous current. Each channel has a separate current input. This allows you to switch 8 independent circuits with the maximum power of a 10A circuit breaker. The 8 external push-button inputs and the status of the relay outputs are displayed separately via the 1-Wire interface. In addition, the status of the relay outputs is displayed via the 1-Wire interface, regardless of whether the relay output was switched via an external button, internal menu or 1-Wire interface.

With the 8-fold digital input module the status of 8 switches, reed contacts or all kinds of digital sensors can be queried. The status of the switch inputs is displayed via the LED indicators on the front panel.When the input voltage is present, the respective LED indicator lights up. Advantage You can acquire 8 digital signals via one module Via manual keys you can simulate an input status without the input being connected. This is very helpful during commissioning or maintenance. Per ESERA extended Plug and Play system, called "Auto-E-Connect", the 8-fold digital input is installed fully automatic in ECO Controller easy and fast. Features Interference immunity: For protect the inputs against interference, the module has filters with a delay of only 30ms. Storage: Even short changes of the input signals are stored. So no signal or pulse can be lost between the reading cycle. Manual function: Each input can be set manually by push button for test purposes, maintenance or development. Isolation: The inputs are isolated from the 1-Wire network by optocouplers. This allows very long connection cables between the module and the sensors without interfering with the 1-Wire bus. In addition, the isolation between switch inputs and 1-Wire network provides increased safety. For the operation of the module we recommend the use of one of our 1-Wire Hub modules.

The brightness of the connected lamps can either be controlled or switched on and off using the touch dimmer function in the living room (extension unit input), via the push-buttons on the top of the module or via the 1-Wire interface. Any push-buttons from all switch ranges can be used for the touch dimmer function. The dimmer response is perceived as very soft and pleasant. You can change the brightness by pressing and holding the living area or module button. You can switch on or off with a short press of the button. The touch dimmer function works with a 12VDC/24VDC DC voltage that does not cause any unwanted interference in its surroundings. This makes the Dual Dimmer ideal for low-radiation areas such as bedrooms and living rooms. In addition to manual control, you also have the option of integrating the leading edge phase control dimmer into your smart home control system. The 1-Wire bus interface is available for this purpose. This dimmer is suitable for light bulbs, dimmable LEDs, high-voltage halogen lamps (ohmic loads), low-voltage halogen lamps (12VDC) and fans (inductive loads) with corresponding power. Note: Low-voltage halogen lamps may only be operated in conjunction with a conventionally wound transformer. Not suitable for loads with electronic ballast, energy-saving and fluorescent lamps. For the living room touch dimmer function, it is sufficient if the dimmer is supplied with the 1-Wire bus voltage (12VDC). This means that the installation in your home is already "smart home ready". This also guarantees that the lighting will work even if the Smart Home control has not yet been programmed or has failed. Overview of the functions: 2-channel leading edge phase control dimmer with soft start and soft dimming behavior Maximum output power: 460W (460VA); with up to 6 LED lamps max. 200W (200VA) Minimum load 6W (6VA) Optionally 32 levels for gentle or 128 levels for very gentle dimming behavior Saving the last dimming level Data output of the current dimming values Status feedback from the digital inputs (push-button interface) Compatible with all 1-Wire control units. Convenient control with the extended range of functions of the ESERA 1-Wire controllers / 1-Wire gateways

Thermal actuator 230V for radiators and floor heating systems Normally closed (M30 x 1.5) Extremely compact design. Quick and easy to install due to very slim design