Rain sensor

Wind sensor Pro 100The compact and professional Wind sensor Pro 100 can record the current wind speed and, e.g. in the event of gusts of wind, provide information via the system control for retracting an awning or raising roller shutters or slats. The Wind sensor Pro 100 is an optimal environmental sensor for recording wind speed for weather recording.All bearings and screws are made of weather-resistant stainless steel and are therefore suitable for professional use in weather stations. Via the S0 interface pulses are output depending on the wind speed. One pulse is emitted per revolution. The Wind sensor Pro 100 has a pulse output and is intended for connection to the 1-Wire S0 counter module (Art. No. 11211). It is weatherproof and has an approx. 2 meter long connection cable. A mast holder, wall bracket and mounting masts are available as accessories. Application Protection of awnings, roller shutters and slats from gusts of wind Recording the wind speed for weather data acquisition Assembly Mounting via M6 screw connection Wall or pole mount bracket Measuring range 0 - 40m/s (0 - 160 Km/s) Interface S0 interface (reed contact, normally open contact) 1 pulses per revolution 1 pulse corresponds to 0.5m/s Electr. values max. 30V, max. 20mA Connection / Cable approx. 2m cable Evaluation Pulse output for 1-Wire S0 counter 11211 Dimensions approx. 210 mm x 80mm (height x width)Wind turbine Ø 160 mm Accessories Pole mount, wall bracket Scope of delivery Wind sensor without mounting bracket

Wind sensor Pro 200 with heating With the compact and professional wind sensor Pro 200, the current wind speed can be recorded and, e.g. in the event of gusts of wind, it can provide information via the system control for retracting an awning or raising roller shutters or slats. The wind sensor Pro 200 is an optimal environmental sensor for recording wind speed for weather recording. For operation in winter the wind sensor Pro 200 is equipped with a heater. This prevents icing and thus a failure of the wind sensor. All bearings and screws are made of weather-resistant stainless steel and are therefore suitable for professional use in weather stations. Via the S0 interface (pulse output) pulses are output depending on the wind speed. 4 pulses are emitted per revolution. The wind sensor Pro 200 has a pulse output and is designed for connection to the 1-Wire Dual S0 counter module (Art. No. 11211). It is weatherproof and has an approx. 3 meter long connection cable. A mast holder, wall bracket and mounting masts are available as accessories. Application Protection of awnings, roller shutters and blinds / slats by gusts of wind Recording of the wind speed for weather data acquisition Assembly Mounting on 50mm mast (antenna mast) Wall or roof bracket Flat roof mast Cable length max. 10m to S0 counter Measuring range 0 - 50m/s (0 - 180 Km/s) Output signal sensor 4 pulses per m/s Electrical values Heating: 24 V AC or DC approx. 0.15W S0 interface (reed contact, normally open contact) 4 pulses per revolution 1 pulse corresponds to 0.25m/s Connection approx. 3m cable, 4-wire Evaluation Pulse output e.g. for 1-Wire S0 counter 11211 See connection example (Download) Dimensions approx. 210 mm x 80mm (height x width) Wind turbine Ø 160 mm Accessories Pole mount, wall bracket, pole for flat roof Scope of delivery Wind sensor without mounting bracket

The 1-Wire Solar Multisensor is a combination sensor for the detection of irradiation, brightness and perceived temperature to control shading and roller shutters in buildings. The solar sensor is for recording the solar irradiation energy over the entire day. The sensor is ideal for controlling shading systems or roller shutters. The detection range for brightness and solar sensor covers a range up to 75000 Lux (divided between a brightness and solar sensor). The sensor is also ideally suited for comparative measurements with existing PV systems. This allows early detection of failures of PV cells, strings or inverters through comparative measurements. A monocrystalline solar cell is used for the solar measurement. The brightness sensor detects the brightness value of the environment in a range of 10 - 7000 Lux, the temperature sensor detects a temperature range of -40 to +85°C. Mounting brackets available as accessories. Note for OWFS: The solar value (xsens) can be read for the DS2438 in the OWFS directory tree in the variable "vis".