1-Wire distributor 7, star-bus topology with push-in connector

1-Wire Dual Digital Input, Board Unassembled printed circuit board for the construction of a 1-Wire digital input. With the 1-Wire dual digital input module two inputs can be monitored independently of each other. A pump or lamp can be monitored as an example. The inputs are connected in parallel to the consumer to be monitored. The dual input module is designed for three variants:- 230V AC voltage - 24V DC voltage - 5V DC voltageConnection: screw terminals for 1-wire bus and input voltageSupply voltage: 1-Wire bus with 5V and 12VCurrent consumption: 5V approx.1mA, 12V approx. 5mA (both inputs active)Installation: Designed for control cabinet installation (top hat rail)Protection class:  IIAssessories: Top hat rail housing (HUT 2)Scope of delivery: Unassembled board in industrial quality without components or housing. Building instructions per downloadNote: Small SMD components must be soldered on the board.

1-Wire switching module Dual 230V 5A top hat rail mounting, board Unassembled printed circuit board for the assembly of a 1-Wire dual switch module.With the Dual Switching Module, two direct current or alternating current consumers can be switched independently of each other. By interconnecting the two channels it is possible to control awnings or tubular motors (roller shutters) (mech. relay version). The module is available in two versions. 1-Wire switch module Dual mech. relay By 5A - Change-over relay for switching AC or DC consumers, all contacts of the relay are led outside- - control of tubular motors for awnings or roller shutters possible 1-Wire Switch Module Dual Electronic Load Relay, Solid State Relay 5A Electronic load relays are the modern way to switch 230V consumers. The switching process is carried out by electronic switches, so there are no malfunctions and no wear and tear of switching contacts as with mechanical relay devices.- Gentle switching of AC 230V consumers - Increased service life of lamps due to zero-crossing control- Practically wear-free Switching current 5A for mech. relay and electronic relay Installation The 1-Wire Dual switch module is designed for control cabinet installation (top-hat rail). Power consumption 5V approx. 1mA, 12V (both outputs active) approx. 30mA Supply voltage 1-Wire Bus, 5V and 12V Connection Screw terminals Protection class II Accessories DS2413 Dual I/O module, top hat rail housing (HUT 2), Elect. Load relays Scope of delivery Unassembled board in industrial quality without components or housing. Building instructions per downloadNote:SMD components must be soldered on the board.

1-Wire 8-fold switch module display board Unassembled printed circuit board (display board) for the assembly of an 8-fold switching module Display board for mounting the 1-Wire 8-fold switch module Installation: Designedfor DIN rail housing Dimensions: 65 x 55mm (WxH) Scope of delivery: Unassembled industrial quality board without components or housing. Building instructions per download Further information, like program examples, data sheets or drivers can be found in our download area

1-Wire 8-Fach Schaltmodul, Leiterplatte ohne Bauteile Unbestückte Leiterplatte zum Aufbau eines 1-Wire 8-Fach Schaltmoduls. Mit dem 1-Wire 8-Fach Schaltmodul können 8 Gleich- oder Wechselspannungsverbraucher geschaltet werden. Das Gerät ist in zwei Gruppen zu je 4 Kanälen aufgebaut. Jede Gruppe hat einen getrennten Stromeingang, der mit  je 5A abgesichert ist. Anzahl Kanäle 8 Schaltstrom 5A pro Ausgang, maximal 5A pro 4-Fachgruppe Schaltspannung Gleich- oder Wechselspannung bis 230V Einbau Für Hutschienengehäuse und Schaltschrankeinbau vorgesehen Anschluß Schraubklemmen für 1-Wire Bus und Schaltkontakte (bis 2,5qmm möglich) Absicherung Sicherungen innenliegend,  2 x Micro Fuse 5A/T Versorgungsspannung 5V und 12V Stromaufnahme 5V ca. 1mA, 12V ca. 100mA (alle Ausgänge aktiv) Schutzklasse II Lieferumfang Unbestückte Platine in Industriequalität ohne Bauteile oder Gehäuse. Bauanleitung per Download Hinweis: Auf der Platine müssen SMD-Bauteile gelötet werden.

1-Wire Dual Reed contact module, board Unassembled printed circuit board for the assembly of a 1-Wire dual reed contact module.With the 1-Wire Dual Reed Contact Sensor Module two independent reed contacts (magnetic switches) can be monitored.The sensor can be used, for example, to monitor a window, door or garage door. 1-Wire interface DS2413 Dual I/O Dimensions 85,8x30,5mm Connection Screw terminals for 1-Wire bus and input voltage (up to 2.5qmm possible) Supply voltage 1-Wire Bus with 5V and 12V Power consumption 5V approx. 1mA, 12V approx. 5mA (both inputs active) Isolation Inputs electrically connected with 1-Wire bus Installation intended for top hat rail housing (switch cabinet installation) Scope of delivery Unassembled board in industrial quality without components or housing.Building instructions per download Cable length between sensor and module It is recommended to use max. 10m cable length. Labelling CE Protection class III Note: SMD components must be soldered on the board

1-Wire 3-fold analog input, 0- 5V or 0 - 10V(Unassembled printed circuit board for the construction of a 1-Wire 3-fold analog input) With the 1-Wire analog input module, three DC voltage sources can be measured independently of each other. As an example, pressure sensors, brightness sensors or other transducers can be read in. The inputs are not isolated from the 1-wire bus and have a ground potential. The module is only intended for the connection of isolated DC voltage sources.The measuring inputs have reverse polarity protection, overvoltage protection and input filters. The measuring range (0-5VDC or 0-10VDC) can be switched by software. number of channels 3 Measuring input 0-5VDC or 0-10VDC Input resistance Input resistance 200k Supply voltage 5V and 12V Power consumption approx. 15mA (all inputs active) Connection Screw terminals for 1-Wire bus and input voltage Isolation No isolation between input and 1-Wire bus Installation Designed for installation in DIN rail housing and control cabinet installation 1-Wire device DS2450(4-fold analog input) Protection class III Scope of delivery Unassembled board in industrial quality without components or housing. Building instructions per download Note: SMD components must be soldered on the board.  

1-Wire Hub II AC with integrated power supply unit unpopulated printed circuit board for the construction of a 1-Wire Hub II AC. The 1-Wire Hub II AC is the central module for building a 1-Wire network. Combination with all 1-Wire devices possible. Designed for control cabinet installation (top hat rail mounting). Via the 1-Wire hub the 1-Wire bus is supplied with 5V and 12V voltage. If the output power of the 1-Wire hub is not sufficient, additional power can be supplied by an external power supply (15V - 24V). Options:- Voltage monitoring of the 5V and 12V voltages by 1-Wire - Voltage and current monitoring of the 5V and 12V by 1-Wire Supply voltage 230VAC Output 5V 0.1A, 12V 0.2A (sum of 5V and 12V 4.5W) LED indicator 5V voltage, 1-Wire activity Dimensions 85 x 77mm, intended for HUT4 top hat rail housing Connection Screw connection Scope of delivery Unassembled board in industrial quality without components or housing. Building instructions per download Note: SMD components must be soldered on the board, depending on the assembly option.

Passive 1-Wire distributor module with 6 outputs for 1-Wire temperature cable sensors with RJ12 connector. The distributor supplements the existing 1-Wire temperature sensor system based on modular RJ12 connectors, enabling fast and cost-sensitive cabling. *Push In terminals are screwless terminal connections.

Passive 1-wire distributor with 6 outputs on RJ45 modular sockets Distributor module for sensors and actuators with RJ45 socket system The distributor supplements the existing 1-Wire cabling system based on network cables. This enables fast and cost-sensitive cabling.

The 1-Wire distributor 6 Professional offers an efficient solution for the linear cabling of 1-Wire sensors in industrial environments and in the IoT sector. With its 6 inputs/outputs on push-in plugs, supplemented by a functional earth, the distributor offers a flexible connection option for various components. Thanks to its compatibility with CAT5, CAT6 and other system cables with 5 cores plus shield, it enables simple integration into existing cabling systems and guarantees a reliable and stable connection. Installation is uncomplicated and time-saving as no screws are required. The push-in clamps enable tool-free installation and prevent unintentional loosening of connections. It is also possible to connect several 1-Wire distributors 6 LIN linearly with each other via system cable. The distributor is compatible with the existing ESERA cabling systems

1-Wire distributor for cabling of 1-Wire sensors in star or tree topology with 6 outputs on push-in terminals* plus one RJ45 modular jack Distribution module for easy cabling in linear bus topology of 1-Wire sensors and actuators. Area of application: Smart Home, Smart Building Designed for CAT5, CAT6 cabling, telephone cables (2 x 2x 0.8qmm) or EIB cables. This allows a fast and cost sensitive cabling. By using Push In terminals you do not need a screwdriver for mounting. Also the times of loosening screws are over. You can connect several 1-Wire Distributors 3 to other 1-Wire Distributors quickly and easily using network patch cables.The distributor complements the existing 1-Wire cabling system based on CAT patch cables. *Push In terminals are screwless terminal connections.