DS2438 Batterie-Management Smart Battery Monitor

DS2401+, 1-Wire Serial Number Module DS2401 Silicone Serial Number Function: Serial number module for 1-Wire bus Housing: TO92 Supply voltage: 2.8V to 5.5V For further data please refer to the data sheet (Download) Hint:We recommend to connect a 100nF (0.1µF) capacitor (see accessories) in parallel to the 1-Wire device, i.e. from 5V to GND. The capacitor should be placed as close as possible. This increases the stability of the entire 1-Wire network.  

1-Wire Adapter USB, DS9490R USB adapter with 1-Wire interface. The adapter provides a quick and easy connection between the computer and the 1-Wire network. Individual 1-Wire sensors can be connected directly. For a network, a 1-Wire Hub or 1-Wire Hub II is recommended as the central power supply. Note: The assignment of the 1-Wire RJ11 socket is different to the 1-Wire cable sensors 11105 and 11106.To connect the 1-Wire adapter to the 1-Wire hub we recommend the adapter cable 11311. - High-Speed 12Mbps Universal Serial Bus (USB) Interface - Supports Standard and Overdrive 1-Wire Communication - Slew-Rate-Controlled 1-Wire Timing and Active Pullup for Improved 1-Wire Network Performance - DS9490R has an RJ11 interface for standard connection - Built-In Custom DS2401 Identification Chip - Reads all 1-Wire and iButton Devices. Writes All Except EPROM 1-Wire/iButton Devices Connection: USB (1.1) to RJ11 (1-Wire)Supply voltage: 5VDC1-Wire device: DS9490

1-Wire Bus Coupler Pro with USB interface, isolation and external power supply With the professional 1-Wire Bus Coupler USB V3 a stable and electrically isolated connection of the 1-Wire network and a PC, mini computer (e.g. Raspberry Pi) or to many other controllers is established. The 1-Wire Bus Coupler USB is compatible with the serial version of Maxim, DS9097 and DS9097E, and works with a standard DS2480 1-Wire master device. By using the 1-Wire standard interface module (DS2480), the 1-Wire bus copller is compatible with all controllers that support this module. These are for example IP-Symcon, FHEM, OpenHub and many more. A special highlight of the 1-Wire Bus Coupler USB V3 is the external power supply. This significantly increases the operational reliability of the data connection to the computer and prevents problems caused by unreliable USB power supplies. The use of more expensive USB hubs is no longer necessary.For the 1-Wire network the 5V output voltage is provided. The insulation prevents interference from and to the PC and reduces possible "electrosmog" in the house. The insulation also increases electrical safety.Individual 1-Wire sensors can be connected directly. For a 1-Wire network, the use of a 1-Wire hub is recommended. Data interface USB 1.1, with FTDI FT232RL Chip (Virtual COM Port) Compatibility To DS9097U 1-Wire Adapter SerialApplicable for many software, such as OWFS, IP-Symcon, FHEM, which is intended for the DS9097U (DS2480 device) Drivers for different operating systems in the download area of this article. Display LED Power and data 1-Wire device DS2480R+ Power supply 9-32 VDC max. 500mA (power supply unit see accessories) Control Control by all devices and controllers that support the DS2480 (serial master) Dimensions 85 x 32 x 70mm Protection circuit Reverse polarity protection for 1-Wire output and supply voltage Isolation Between 1-Wire bus and PC interface min. 500VDC Scope of delivery Finished device and operating instructions

1-Wire Dual Digital I/O Chip Actuator for 2 channel digital input or output Temperature range: -55 to +85°C- Supply voltage: 2.8V - 5.25VHousing: TOSC 8 Type :DS2413P+PIO Pins Support 20mA max Continuous Current Sink - Supports 28V (max) PIO Pin Operating Voltage - On-Resistance of PIO Pulldown Transistor 20mA, max; OFF Resistance 1MOhm - Parasitic Power Supply Through 1-Wire  

DS2408, 1-wire 8-fold digital I/O module Dallas Addressable 8-Port Switch, switching module for 8-fold digital input or digital outputTemperature range: -40°C to +85°C Supply voltage: 2.8V to 5.25VType: DS2408S+ Hint:We recommend to connect a 100nF (0.1µF) capacitor (see accessories) in parallel to the 1-Wire device, i.e. from 5V to GND. The capacitor should be placed as close as possible. This increases the stability of the entire 1-Wire network.

DS2423 1-Wire Dual Counter Module / DS2423 1-Wire Dual Counter Function: Dual counter module for 1-Wire network 2x 32Bit counter Housing: 6-pin TSOC SMD Housing Supply voltage: 2.8V to 5.25V Module not resettable. For further data please refer to the data sheet Hint:We recommend to connect a 100nF (0.1µF) capacitor (see accessories) in parallel to the 1-Wire device, i.e. from 5V to GND. The capacitor should be placed as close as possible. This increases the stability of the entire 1-Wire network.

DS2406+, 1-Wire Dual Switch with 1K memory DS2406 Dual Addressable Switch Plus 1Kb Memory Function: 1 channel I/O module for 1-Wire bus Housing: TO92 Supply voltage: 2.8V to 5.5V Switching voltage/current max. 13V, max. 0.1A For further data please refer to the data sheet Hint:We recommend to connect a 100nF (0.1µF) capacitor (see accessories) in parallel to the 1-Wire device, i.e. from 5V to GND. The capacitor should be placed as close as possible. This increases the stability of the entire 1-Wire network.

DS2480B+ Bus master, serial to 1-Wire deviceDS2480B+ Serial 1-Wire Line Driver with Load Sensor Function: Bus master serial for 1-Wire with load sensor Housing: TO 8 Supply voltage: 2.8V to 5.25V   For further data please refer to the data sheet   Hint: We recommend to connect a 0.1µF capacitor (ceramic) in parallel to the 1-Wire device, i.e. from 5V to GND. The capacitor should be placed as close as possible. This increases the stability of the entire 1-Wire network.