USB Cable 0.5m A-B

1-Wire Bus Coupler Pro with USB interface, isolation and external power supply With the professional 1-Wire Bus Coupler USB V3 a stable and electrically isolated connection of the 1-Wire network and a PC, mini computer (e.g. Raspberry Pi) or to many other controllers is established. The 1-Wire Bus Coupler USB is compatible with the serial version of Maxim, DS9097 and DS9097E, and works with a standard DS2480 1-Wire master device. By using the 1-Wire standard interface module (DS2480), the 1-Wire bus copller is compatible with all controllers that support this module. These are for example IP-Symcon, FHEM, OpenHub and many more. A special highlight of the 1-Wire Bus Coupler USB V3 is the external power supply. This significantly increases the operational reliability of the data connection to the computer and prevents problems caused by unreliable USB power supplies. The use of more expensive USB hubs is no longer necessary.For the 1-Wire network the 5V output voltage is provided. The insulation prevents interference from and to the PC and reduces possible "electrosmog" in the house. The insulation also increases electrical safety.Individual 1-Wire sensors can be connected directly. For a 1-Wire network, the use of a 1-Wire hub is recommended. Data interface USB 1.1, with FTDI FT232RL Chip (Virtual COM Port) Compatibility To DS9097U 1-Wire Adapter SerialApplicable for many software, such as OWFS, IP-Symcon, FHEM, which is intended for the DS9097U (DS2480 device) Drivers for different operating systems in the download area of this article. Display LED Power and data 1-Wire device DS2480R+ Power supply 9-32 VDC max. 500mA (power supply unit see accessories) Control Control by all devices and controllers that support the DS2480 (serial master) Dimensions 85 x 32 x 70mm Protection circuit Reverse polarity protection for 1-Wire output and supply voltage Isolation Between 1-Wire bus and PC interface min. 500VDC Scope of delivery Finished device and operating instructions

KNX USB-Interface for extending the ESERA station for integration into KNX systems The KNX interface is used to establish a bidirectional connection KNX network between the ESERA station or a PC and the installation bus KNX. The connection is established via USB cable. The device can also be used as a programming interface for the ETS. The device is supplied via the USB and KNX bus and does not require any additional power supply. The LEDs on the front of the device visualize the connection status, the telegram traffic and communication errors for USB and KNX. It supports KNX Long Frames and is used to establish a bidirectional KNX network connection between a PC and the KNX installation bus. Interface: USB port is galvanically isolated from the KNX bus. The interface is compatible with ETS (Engineering Tool Software) from ETS3 and higher. The device has a complete KNX stack with communication objects and BAOS protocol V2 implemented. Thus it offers the possibility to extend the ESERA station or other devices with USB connection to full KNX functionality, which can then even be programmed by ETS. KNX interface KNX Bus Twisted Pair, Compatible with ETS from ETS3 on, support of KNX Long Frames, USB connector is galvanically isolated from the KNX bus. The interface is compatible with ETS (Engineering Tool Software) as of ETS3, the device has implemented a complete KNX stack with communication objects and BAOS protocol V2. Thus it offers the possibility to extend devices with USB connection to full KNX functionality, which can then even be programmed by ETS. KNX data interface: Terminal for KNX BUS (red / black) Protocol: KNX Stack with communication objects and BAOS protocol V2 Supply voltage: KNX bus and USB Power consumption approx. < 100mW (USB) or <100 mW (KNX) Dimensions: In-line installation, installation width 1 TE, 18 mm Connection: Terminal for KNX BUS (red / black), USB socket, type B Manufacturer / Type Weinzierl / KNX IP BAOS 721 Assembly: Designed for top hat rail Scope of delivery: KNX Ethernet Interface, Data Sheet

EBC 100 eBus coupler USB: the data interface to the eBus via USB for PC, Raspberry Pi and co. Application The eBus coupler enables read and write access to the eBus of your heating system (Physical layer OSI 1) By using the appropriate software, you can analyze data from your heating system and send new values to your heating control system via the eBus. Features The ESERA eBus coupler is equipped with galvanic isolation between the eBus and PC interface. The eBus input is bipolar, so you do not need to pay attention to the polarity of the eBus when connecting.LED display for “USB Power” and “eBus Power” and “Activity” The eBus coupler is equipped with a USB interface from the manufacturer FTDI as a data interface to your PC. Drivers for Windows, Linux and other operating systems are available on the FTDI website. The housing of the eBus coupler is designed for switch cabinet installation. Notes The eBus coupler is not supported by the Vaillant vrDIALOG software. We recommend using a USB hub with a power supply unit as a power supply. This ensures a continuous power supply independent of a Raspberry Pi, for example Examples (VWMon from Alexey Ozerov) for reading out eBus data you will find, among other things hier or the project Fhem click here