Power supply 12VDC 1A

Quantity Unit price
1 to 49
€9.90*
50 to 99
€9.41*
From 100
€8.91*

Available, delivery time 1-5 days, depending on the carrier

Product number: 61051
EAN: 0098931699899
Manufacturer product ID: 61051
Product information "Power supply 12VDC 1A"

Switching power supply 12V 1A, plug-in power supply AC/DC

HNP12-120

Energy-saving plug-in power supply unit for supplying electronic assemblies

- Power supply with European plug
- wide range input 100-240VAC
- short circuit and overload protection
- insulation class 2 (protection class 2)
- complies with Energy Star Level IV


Manufacturer:
HN-Power
Model: HNP12
Connection: Input: Euro plug, Output: Hollow plug
Input: 100-- 240VAC,

Output: 12V, 1A. 12W

Output plug: 2.1 x 5.5 x 10 mm,inside positive, outside negative

Connection: 1,5m
Operating temperature: -5...+40°C
Efficiency: 70%





.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.


Device Documentation Operating instructions, connection diagram, conformity, ...
Info Material Product catalogue, Brochures
Technical Downloads Software & co.
Worth knowing Wikis, entries, tutorials

Accessories

eBus to serial Coupler
 eBus to seriell coupler The eBus Coupler Serial provides read and write access to the eBus network. Thus with appropriate software it is possible to analyze all of your home heating system data and provide it with new operating data.The E-Service eBus Coupler Serial provides galvanic isolation between the eBus and the PC serial interface. The built-in software filter ensures that only payload data is transmitted over the serial interface. This filter significantly reduces the amount of data being transferred.The eBus interface is reverse polarity protected. Therefore it is not necessary to observe signal polarity when connecting to the eBus. The Coupler’s enclosure is designed for mounting within a control cabinet.The eBus coupler is equipped with an RS232 serial interface for transferring data to and from the PC. On the Coupler’s front panel there are LED indicators for “PWR” (eBus input power) and “DATA” (eBus activity). In the area of the eBus terminals there is additional a green LED which indicates the presence of an eBus. An external power adapter which is not included as part of the eBus Coupler delivery is required to operate the eBus Coupler. A very good example from VWMon of Alexey Ozerov for reading data eBus see you can found here or the project FHEM here

From €73.71*

Product number: 12003

Available, delivery time 1-5 days, depending on the carrier

eBUS Coupler Ethernet
eBus coupler USB: eBus to USB data interface for PC, Raspberry Pi and Co Application With the eBus coupler you can access the eBUS e.g. of your heating system in read and write mode. With appropriate software, you can evaluate data from your heating system and send new values to your heating control system via the eBUS. Features With the eBus coupler you can access the eBUS e.g. of your heating system in read and write mode. With appropriate software, you can evaluate data from your heating system and send new values to your heating control system via the eBUS. The eBus coupler is equipped with a galvanic isolation between eBus and PC interface. The eBus input is bipolar, so you do not need to pay attention to the polarity of the eBus when connecting. The housing of the eBus coupler is designed for control cabinet installation. As data interface to your PC, the eBus coupler is equipped with an Ethernet interface. Drivers for Windows operating systems are available.The eBus coupler is not supported by Vaillant vrDIALOG software. A very good example (VWMon by Alexey Ozerov) for reading out eBus data can be found here or the project Fhem here

From €127.71*

Product number: 12002

Available, delivery time 1-5 days, depending on the carrier

1-Wire Bus Coupler USB Pro, isolated
1-Wire Bus Coupler Pro with USB interface, isolation and external power supply With the professional 1-Wire Bus Coupler USB V3 a stable and electrically isolated connection of the 1-Wire network and a PC, mini computer (e.g. Raspberry Pi) or to many other controllers is established. The 1-Wire Bus Coupler USB is compatible with the serial version of Maxim, DS9097 and DS9097E, and works with a standard DS2480 1-Wire master device. By using the 1-Wire standard interface module (DS2480), the 1-Wire bus copller is compatible with all controllers that support this module. These are for example IP-Symcon, FHEM, OpenHub and many more. A special highlight of the 1-Wire Bus Coupler USB V3 is the external power supply. This significantly increases the operational reliability of the data connection to the computer and prevents problems caused by unreliable USB power supplies. The use of more expensive USB hubs is no longer necessary.For the 1-Wire network the 5V output voltage is provided. The insulation prevents interference from and to the PC and reduces possible "electrosmog" in the house. The insulation also increases electrical safety.Individual 1-Wire sensors can be connected directly. For a 1-Wire network, the use of a 1-Wire hub is recommended. Data interface USB 1.1, with FTDI FT232RL Chip (Virtual COM Port) Compatibility To DS9097U 1-Wire Adapter SerialApplicable for many software, such as OWFS, IP-Symcon, FHEM, which is intended for the DS9097U (DS2480 device) Drivers for different operating systems in the download area of this article. Display LED Power and data 1-Wire device DS2480R+ Power supply 9-32 VDC max. 500mA (power supply unit see accessories) Control Control by all devices and controllers that support the DS2480 (serial master) Dimensions 85 x 32 x 70mm Protection circuit Reverse polarity protection for 1-Wire output and supply voltage Isolation Between 1-Wire bus and PC interface min. 500VDC Scope of delivery Finished device and operating instructions

From €89.91*

Product number: 11302-U

Available, delivery time 1-5 days, depending on the carrier

Controller 1, 1-Wire to Serial RS232
1-Wire Controller 1 Ethernet, the intelligent system interface to all Smarthome controllers The 1-Wire Controller 1 enables the connection of inexpensive 1-Wire sensors/modules with all types of µcontrollers, PLC or PC systems without special knowledge of the 1-Wire protocol.1-Wire Bus to Serial RS232Controller 1 is the autonomous management of 1-Wire devices in a 1-Wire network, automatically detecting new 1-Wire devices and cyclically supplying the current values. The output is formatted as ASCII characters and sent via the computer interface to the higher-level control system. For example, temperature sensors provide you with the temperature in plain text. The device has extensive configuration and formatting options, which are read and operated via terminal program (e.g. HTerm or Putty). Up to 30 1-Wire devices can be operated in parasitic and standard mode. The 1-Wire interface is designed for operation with small to large 1-Wire networks. Supported chips: DS2401 (electronic key (iButton)), DS1820, DS18S20, DS18B20, DS2405, DS2413, DS2408, DS2423, DS2438 and DS2450 Interface: 1-Wire to Serial RS232Supply voltage: 9-30VDCOutput: 5V max.0,2A Dimensions: 32 x 71x 90mm (WxHxD) Mounting: Designed for DIN rail Connection: Screw terminalsScope of delivery: Module and operating instructions

From €125.91*

Product number: 11320

Available, delivery time 1-5 days, depending on the carrier

1-Wire bus coupler with RS232 (V24 interface), industrial version, galvanic isolation, DS2480
DIN rail adapter between PC and 1-Wire network, Serial to 1-WireIndustrial 1-Wire bus coupler with RS232 (V24) in industrial design with galvanic isolation between the data and 1-Wire bus interface.1-Wire bus coupler RS232 in DIN rail housing. With the 1-Wire Bus Coupler a fast and simple connection between computer and 1-Wire network or to the PLC via a serial terminal is possible.State-of-the-art high-speed optocouplers and DC/DC power supplies are used for safe galvanic isolation. Even the 1-Wire activity LED has an isolated design. The isolation prevents interference to and from the PC and reduces possible "electrosmog" in the building. The isolation also increases electrical safety.For the 1-Wire network, the 5V output voltage is 250mA max.Single 1-Wire sensors can be connected directly. For a 1-Wire network, the use of a 1-Wire hub is recommended.LED indicators for power and activity.

From €89.91*

Product number: 11302-R

Available, delivery time 1-5 days, depending on the carrier

1-Wire bus coupler with RS232 (TTL 5V), industrial version, galvanic isolation
DIN rail adapter between PC and 1-Wire networkIndustrial 1-Wire bus coupler with RS232 (TTL 5V standard) in industrial design with galvanic isolation between the data and 1-Wire bus interface.1-Wire bus coupler RS232 in DIN rail housing. With the 1-Wire Bus Coupler a fast and easy connection between computer and 1-Wire network or to the PLC via a serial terminal is possible.State-of-the-art high-speed optocouplers and DC/DC power supplies are used for safe galvanic isolation. Even the 1-Wire activity LED has an isolated design. The isolation prevents interference to and from the PC and reduces possible "electrosmog" in the building. The isolation also increases electrical safety.For the 1-Wire network, the 5V output voltage is 250mA max.Single 1-Wire sensors can be connected directly. For a 1-Wire network, the use of a 1-Wire hub is recommended.LED indicators for power and activity.Note: The data interface is designed as a D-Sub socket.

From €89.91*

Product number: 11302-T

Available, delivery time 1-5 days, depending on the carrier