Electricity meter three-phase current

Product information "Electricity meter three-phase current"

Three-phase meter with analog display for top-hat rail

With this three-phase meter you can monitor and measure the electricity consumption of large consumers, a house or an apartment.
The S0 output impulses can e.g. be recorded by 1-Wire S0 meters and evaluated by software.

The three-phase meter is intended for installation in the fuse box on the house or apartment and must be installed by a qualified electrician in accordance with the applicable regulations.

Measuring current range 3 x 10(63) A
Voltage range

3 x 230 / 400 VAC, 50 / 60Hz

Display

Analogue 6+1 (=999999.9 kWh), counter reading is maintained even when no current is applied

Design

Meter according to IEC62051-11 2003, IEC62053-21 2003

Accuracy class 1
Power consumption >= 10VA (2W)
Pulse output S0 Optically decoupled, 5 - 27V and max. 27mA
Resolution 800 pulses / kWh = 1 pulse / Watt
S0 connection cable max. 20m
Display LED LED flashes red when power consumption
Operating temperature range -20°C to +45°C
Assembly Top hat rail mounting 122mm / TE (DIN 43880)
Dimensions incl. cover caps 7 TE, 118 x 122 x 63mm (LxWxD)
Dimensions without cover caps 91 x 122 x 63mm (LxWxD)
Connection Screw terminals for wires up to 16mm²
Scope of delivery Electricity meter and data sheet

When connected, the covers over the terminals must be kept closed!
Technical changes and errors excepted.

Accuracy class: 1
Connection type: Screw terminals for conductors up to 16mm²
Dimensions:
  • 7 TE, 118 x 122 x 63mm (LxWxD) incl. cover caps
  • 91 x 122 x 63mm (LxWxD) without cover caps
Display: Analog 6+1 (=9999.9 kWh), counter reading is retained even when no power is supplied
Display LED: LED flashes red on power consumption
Execution: Meter according to IEC62051-11 2003, IEC62053-21 2003
Measuring current range: 3 x 10(63) A
Mounting: Top hat rail mounting 122mm / TE (DIN 43880)
Power Consumption: >= 10VA (2W)
Pulse output S0: Optically decoupled, 5 - 27V and max. 27mA
Resolution: 800 pulses / kWh = 1 pulse / watt
S0 connection cable: max. 20m
Scope of delivery: Device and Quick Guide, the User Guide (Manual) can be found in the download area as a PDF download.
Temperature range, operation: -20°C to +45°C
Voltage range: 3 x 230 / 400 VAC, 50 / 60Hz

0 of 0 reviews

Leave a review!

Share your experiences with other customers.


Device Documentation Operating instructions, connection diagram, conformity, ...
Info Material Product catalogue, Brochures
Technical Downloads Software & co.
Worth knowing Wikis, entries, tutorials
Tip
1-Wire Dual S0 counter module PRO
The 1-Wire S0 Meter Pro is designed for energy metering of two independent electricity, water and gas meters or the wind turbine. All S0 energy meters manufactured according to DIN 43864 can be reliably measured. Due to the high-quality electronics of the 1-Wire S0 Meter Pro, energy meters can also be reliably recorded with very high pulse frequencies of up to 300 Hz. The S0 meter values are made available via a 1-Wire bus interface. In the event of a power failure, the S0 meter values are permanently stored internally for at least 99 years. Inputs 2 x S0 pulse input (counter) for 2 energy meters or wind sensor Supply voltage 12V 1-Wire Bus Power consumption 10mA, both inputs active S0 Interface 10V and approx. 4mA working level, according to DIN 43864 Counter range / scope 32 bit counter per S0 input Data preservation / storage Permanent storage of meter values for up to 99 years in the event of a power failure Data interface 1-Wire Interface, DS2423 command set (GND, Data and 12V) Operating voltage 12VDC (+10% / -20%) Power consumption max. 10mA Operating frequency S0 Input max. 300Hz Connection Screw terminals for 1-Wire bus and S0 inputs up to 2,5qmm cable cross section Dimensions 1HP, 17 x 71x 90mm (WxHxD) Protection class III Note The counter value can be reset via push button on the front panel Installation Designed for control cabinet installation (top hat rail) Scope of delivery Finished device and operating instructions

From €59.31*

Product number: 11211

Available, delivery time 1-5 days, depending on the carrier

Electricity meter alternating current
Electronic single-phase alternating current meter Electronic alternating current meter with analogue display for DIN top-hat rail. The electricity meter is designed for quick snap-in mounting on DIN top-hat rails and is therefore ideal for monitoring the consumed KWh in houses, apartments or individual devices in almost all installation cabinets and electrical boxes. The S0 output pulses can be evaluated e.g. by a 1-Wire S0 counter.Top hat rail mounting 18mm / TE (DIN 43880), screw terminal connections for conductors up to 16qmm Voltage range Nominal 230VAC (184V to 265V), 50 - 60Hz Measuring current range 0.02A (type) up to 32A Display 5 digits for kilowatt hours and 2 decimal places Accuracy class 1 Resolution S0 1000 pulses / kWh = 1 pulse / Watt Pulse output S0 Optically decoupled, 5 - 27V and max. 27mA Operating temperature range -20°C to +65°C Power consumption 8VA < 0.4W Dimensions incl. cover caps 118 x 18 x 63mm (LxWxD) Dimensions without cover caps 91 x 18 x 63mm (LxWxD) Scope of delivery Electricity meter Note:When connected, the covers over the terminals must be kept closed.The AC meter is intended for installation in the fuse box and must be installed by a qualified electrician in accordance with the applicable regulations.Technical changes and errors excepted.

From €23.31*

Product number: 96001

Available, delivery time 1-5 days, depending on the carrier