Station-200 RS485 extension

Quantity Unit price
1 to 49
€25.13*
50 to 99
€23.87*
From 100
€22.61*

Available, delivery time 1-5 days, depending on the carrier

Product number: 19201
EAN: 0098931698878
Manufacturer product ID: 19201
Product information "Station-200 RS485 extension"

Station 200 RS485 extension (hardware)

Internal extension module for the Station-200. This extension adds an RS485 interface to the Station-200, e.g. for Modbus RTU.
The RS485 extension creates a bidirectionally usable bus system that can be operated with up to 128 devices with very long lines on one bus.

Features:
RS485 interface with galvanic isolation between station-200 and RS485 bus Terminating resistor with 120 Ohm integrated transmission speed (baud rate) and protocol, e.g. Modbus RTU, is defined by software no additional space required in the control cabinet, as the internal installation space of the Station-200 is used professional connection via push-in connector system
Only operation of RS485 extension is not provided Can only be used in conjunction with the Station-200.
Technical dataRS485 interface:
  • 1 x Galvanically isolated RS485 data interface for Station-200
  • Isolation between station and RS485 bus, min. 500VDC
  • Half duplex interface, usable as master or slave operation
  • connection: push in terminal, 4-pole for cable up to 1,5qmm cross-section
  • max. cable length: up to 1200m*
  • Termination internal: 120 Ohm available (activation via cable jumper at connector)
  • Application: data interface e.g. for electricity meters, inverters or other devices with serial data interface


Connection type: Push In connector / connection
Data interface: Modbus/TCP, Serial (RS485 Technology)
Design / Manufacturer: ESERA
Enclosure: Open housing, open assembly / printed circuit board
Execution: 4 pin connector
Function:
  • Accessories for sensors (outdoor)
  • Bus - interface, without integrated intelligence
  • Sensor Accessories (General)
Humidity Operation / Storage: 10% to 92% (non-condensing)
Ingress Protection (IP = protection class according to DIN EN 60529), protection class (DIN EN 61140 (VDE 0140-1):
  • IP00
  • Protection class III
Number of inputs / outputs: 1 - channel output
Protection circuit: Enhanced ESD protection with ±4kV according to IEC 61000-4
Scope of delivery: Device and Quick Guide, the User Guide (Manual) can be found in the download area as a PDF download.
Temperature range, operation: -25°C to +70°C, Extended temperature range 1, (E1)
Temperature range, storage: -25°C bis +70°C, Extended temperature range 1, (E1)
Version: Professional Version / Professional Serie

0 of 0 reviews

Leave a review!

Share your experiences with other customers.


Device Documentation Operating instructions, connection diagram, conformity, ...
Info Material Product catalogue, Brochures
Technical Downloads Software & co.
Worth knowing Wikis, entries, tutorials

Accessories

Tip
ESERA-Station 200 Smart Home IoT
Software Version / Support: IP-Symcon Basic
ESERA-Station 200 - expandable, open and future-proof Central control with integrated professional 1-Wire interface for Smart Building, IoT and general automation applicationsTheESERA-Station is the central control unit of your Smart Home and for Internet of Things (IoT). The ESERA station is more like another central controller. It is an open platform, is a combination of an embedded computer and professional ESERA ECO controller. It is an open automation control center built on standards.ESERA station is usable for a variety of software packages, Codesys*****, IP-Symcon, OpenHAB, FHEM, NodeRed and many more, built on a Raspberry Pi 3b.Thefollowing modules are integrated in the ESERA-Station 200:Powerful ARM Quad Core Embedded Computer, Raspberry Pi 3b New in 2021ECO 200 1-Wire controller of the latest generationwithPlug and Play system (Auto-E-Connect Support) for 1-Wire.No matter which IoT or automation system you are already using or still planning to use, you can combine them with ESERA Station 200.You can combine the following systems with ESERA Station 200: The listed systems are exemplary and depend on the installed application software and hardware extensions. Wired / Cable systems / Bus systems*** (Exemplary) Radio based / Radio systems*** (Exemplary) ESERA 1-Wire Gateway (ASCII and Modbus RTU software interface) EnOcean* KNX* (IP-Symcon, Codesys*****) HomeMatic* digitalSTROM* (IP-Symcon) XBee/Zigbee* LCN* (IP-Symcon) xComfort* DMX lighting technology** (IP-Symcon) Z-Wave* ModBus TCP/RTU**, Slave / Master (IP-Symcon, Codesys*****) Voice control from Amazon (Alexa)*, *** M-Bus* (IP-Symcon) PLC Siemens* / WAGO* / Beckhoff* (IP-Symcon, Codesys*****) PROFINET Controller / Device (Codesys*****) EtherCAT Master (Codesys*****) CANopen Master / Slave (Codesys*****) EtherNet/IP Scanner / Adapter (Codesys*****) * An additional gateway is required for operation. This is not included in the scope of delivery.** The optional RS485 interface is required for operation. The RS485 interface can be ordered together with the Station 200.*** The functions depend on the installed application software. The listed systems are related to the operation with IP-Symcon and Codesys and are to be understood as an example. The scope of functions can be found in the respective application software.**** ESERA sensors and actuators of the Pro series with Auto-E-Connect support are required.***** The offered CODESYS Runtime is intended for testing and teaching purposes. All scripts, software modules and extensions of IP-Symcon can be used. To manage and configure your smart home or smart system, the IP-Symcon management console is available for temptation. After installing the runtime environment, the Raspberry Pi can be programmed as a PLC using the CODESYS Development System.The product is installed into the Linux distribution Raspbian via the CODESYS Development System using the included CODESYS Deploy Tool extension. After each restart of the Raspberry Pi, the runtime system is automatically started.

Variants from €392.31*
From €492.21*

Product number: 19200-2

Available, delivery time 1-5 days, depending on the carrier

Tip
ESERA-Station 200 Smart Home IoT
Software Version / Support: without software
ESERA-Station 200 - expandable, open and future-proof Central control with integrated professional 1-Wire interface for Smart Building, IoT and general automation applicationsTheESERA-Station is the central control unit of your Smart Home and for Internet of Things (IoT). The ESERA station is more like another central controller. It is an open platform, is a combination of an embedded computer and professional ESERA ECO controller. It is an open automation control center built on standards.ESERA station is usable for a variety of software packages, Codesys*****, IP-Symcon, OpenHAB, FHEM, NodeRed and many more, built on a Raspberry Pi 3b.Thefollowing modules are integrated in the ESERA-Station 200:Powerful ARM Quad Core Embedded Computer, Raspberry Pi 3b New in 2021ECO 200 1-Wire controller of the latest generationwithPlug and Play system (Auto-E-Connect Support) for 1-Wire.No matter which IoT or automation system you are already using or still planning to use, you can combine them with ESERA Station 200.You can combine the following systems with ESERA Station 200: The listed systems are exemplary and depend on the installed application software and hardware extensions. Wired / Cable systems / Bus systems*** (Exemplary) Radio based / Radio systems*** (Exemplary) ESERA 1-Wire Gateway (ASCII and Modbus RTU software interface) EnOcean* KNX* (IP-Symcon, Codesys*****) HomeMatic* digitalSTROM* (IP-Symcon) XBee/Zigbee* LCN* (IP-Symcon) xComfort* DMX lighting technology** (IP-Symcon) Z-Wave* ModBus TCP/RTU**, Slave / Master (IP-Symcon, Codesys*****) Voice control from Amazon (Alexa)*, *** M-Bus* (IP-Symcon) PLC Siemens* / WAGO* / Beckhoff* (IP-Symcon, Codesys*****) PROFINET Controller / Device (Codesys*****) EtherCAT Master (Codesys*****) CANopen Master / Slave (Codesys*****) EtherNet/IP Scanner / Adapter (Codesys*****) * An additional gateway is required for operation. This is not included in the scope of delivery.** The optional RS485 interface is required for operation. The RS485 interface can be ordered together with the Station 200.*** The functions depend on the installed application software. The listed systems are related to the operation with IP-Symcon and Codesys and are to be understood as an example. The scope of functions can be found in the respective application software.**** ESERA sensors and actuators of the Pro series with Auto-E-Connect support are required.***** The offered CODESYS Runtime is intended for testing and teaching purposes. All scripts, software modules and extensions of IP-Symcon can be used. To manage and configure your smart home or smart system, the IP-Symcon management console is available for temptation. After installing the runtime environment, the Raspberry Pi can be programmed as a PLC using the CODESYS Development System.The product is installed into the Linux distribution Raspbian via the CODESYS Development System using the included CODESYS Deploy Tool extension. After each restart of the Raspberry Pi, the runtime system is automatically started.

From €392.31*

Product number: 19200-1

Available, delivery time 1-5 days, depending on the carrier

Tip
ESERA-Station 200 Smart Home IoT
Software Version / Support: CODESYS 3.x
ESERA-Station 200 - expandable, open and future-proof Central control with integrated professional 1-Wire interface for Smart Building, IoT and general automation applicationsTheESERA-Station is the central control unit of your Smart Home and for Internet of Things (IoT). The ESERA station is more like another central controller. It is an open platform, is a combination of an embedded computer and professional ESERA ECO controller. It is an open automation control center built on standards.ESERA station is usable for a variety of software packages, Codesys*****, IP-Symcon, OpenHAB, FHEM, NodeRed and many more, built on a Raspberry Pi 3b.Thefollowing modules are integrated in the ESERA-Station 200:Powerful ARM Quad Core Embedded Computer, Raspberry Pi 3b New in 2021ECO 200 1-Wire controller of the latest generationwithPlug and Play system (Auto-E-Connect Support) for 1-Wire.No matter which IoT or automation system you are already using or still planning to use, you can combine them with ESERA Station 200.You can combine the following systems with ESERA Station 200: The listed systems are exemplary and depend on the installed application software and hardware extensions. Wired / Cable systems / Bus systems*** (Exemplary) Radio based / Radio systems*** (Exemplary) ESERA 1-Wire Gateway (ASCII and Modbus RTU software interface) EnOcean* KNX* (IP-Symcon, Codesys*****) HomeMatic* digitalSTROM* (IP-Symcon) XBee/Zigbee* LCN* (IP-Symcon) xComfort* DMX lighting technology** (IP-Symcon) Z-Wave* ModBus TCP/RTU**, Slave / Master (IP-Symcon, Codesys*****) Voice control from Amazon (Alexa)*, *** M-Bus* (IP-Symcon) PLC Siemens* / WAGO* / Beckhoff* (IP-Symcon, Codesys*****) PROFINET Controller / Device (Codesys*****) EtherCAT Master (Codesys*****) CANopen Master / Slave (Codesys*****) EtherNet/IP Scanner / Adapter (Codesys*****) * An additional gateway is required for operation. This is not included in the scope of delivery.** The optional RS485 interface is required for operation. The RS485 interface can be ordered together with the Station 200.*** The functions depend on the installed application software. The listed systems are related to the operation with IP-Symcon and Codesys and are to be understood as an example. The scope of functions can be found in the respective application software.**** ESERA sensors and actuators of the Pro series with Auto-E-Connect support are required.***** The offered CODESYS Runtime is intended for testing and teaching purposes. All scripts, software modules and extensions of IP-Symcon can be used. To manage and configure your smart home or smart system, the IP-Symcon management console is available for temptation. After installing the runtime environment, the Raspberry Pi can be programmed as a PLC using the CODESYS Development System.The product is installed into the Linux distribution Raspbian via the CODESYS Development System using the included CODESYS Deploy Tool extension. After each restart of the Raspberry Pi, the runtime system is automatically started.

Variants from €392.31*
From €540.81*

Product number: 19200-5

Available, delivery time 1-5 days, depending on the carrier

Tip
ESERA-Station 200 Smart Home IoT
Software Version / Support: IP-Symcon Unlimited
ESERA-Station 200 - expandable, open and future-proof Central control with integrated professional 1-Wire interface for Smart Building, IoT and general automation applicationsTheESERA-Station is the central control unit of your Smart Home and for Internet of Things (IoT). The ESERA station is more like another central controller. It is an open platform, is a combination of an embedded computer and professional ESERA ECO controller. It is an open automation control center built on standards.ESERA station is usable for a variety of software packages, Codesys*****, IP-Symcon, OpenHAB, FHEM, NodeRed and many more, built on a Raspberry Pi 3b.Thefollowing modules are integrated in the ESERA-Station 200:Powerful ARM Quad Core Embedded Computer, Raspberry Pi 3b New in 2021ECO 200 1-Wire controller of the latest generationwithPlug and Play system (Auto-E-Connect Support) for 1-Wire.No matter which IoT or automation system you are already using or still planning to use, you can combine them with ESERA Station 200.You can combine the following systems with ESERA Station 200: The listed systems are exemplary and depend on the installed application software and hardware extensions. Wired / Cable systems / Bus systems*** (Exemplary) Radio based / Radio systems*** (Exemplary) ESERA 1-Wire Gateway (ASCII and Modbus RTU software interface) EnOcean* KNX* (IP-Symcon, Codesys*****) HomeMatic* digitalSTROM* (IP-Symcon) XBee/Zigbee* LCN* (IP-Symcon) xComfort* DMX lighting technology** (IP-Symcon) Z-Wave* ModBus TCP/RTU**, Slave / Master (IP-Symcon, Codesys*****) Voice control from Amazon (Alexa)*, *** M-Bus* (IP-Symcon) PLC Siemens* / WAGO* / Beckhoff* (IP-Symcon, Codesys*****) PROFINET Controller / Device (Codesys*****) EtherCAT Master (Codesys*****) CANopen Master / Slave (Codesys*****) EtherNet/IP Scanner / Adapter (Codesys*****) * An additional gateway is required for operation. This is not included in the scope of delivery.** The optional RS485 interface is required for operation. The RS485 interface can be ordered together with the Station 200.*** The functions depend on the installed application software. The listed systems are related to the operation with IP-Symcon and Codesys and are to be understood as an example. The scope of functions can be found in the respective application software.**** ESERA sensors and actuators of the Pro series with Auto-E-Connect support are required.***** The offered CODESYS Runtime is intended for testing and teaching purposes. All scripts, software modules and extensions of IP-Symcon can be used. To manage and configure your smart home or smart system, the IP-Symcon management console is available for temptation. After installing the runtime environment, the Raspberry Pi can be programmed as a PLC using the CODESYS Development System.The product is installed into the Linux distribution Raspbian via the CODESYS Development System using the included CODESYS Deploy Tool extension. After each restart of the Raspberry Pi, the runtime system is automatically started.

Variants from €392.31*
From €884.61*

Product number: 19200-4

Available, delivery time 1-5 days, depending on the carrier

Tip
ESERA-Station 200 Smart Home IoT
Software Version / Support: IP-Symcon Professional
ESERA-Station 200 - expandable, open and future-proof Central control with integrated professional 1-Wire interface for Smart Building, IoT and general automation applicationsTheESERA-Station is the central control unit of your Smart Home and for Internet of Things (IoT). The ESERA station is more like another central controller. It is an open platform, is a combination of an embedded computer and professional ESERA ECO controller. It is an open automation control center built on standards.ESERA station is usable for a variety of software packages, Codesys*****, IP-Symcon, OpenHAB, FHEM, NodeRed and many more, built on a Raspberry Pi 3b.Thefollowing modules are integrated in the ESERA-Station 200:Powerful ARM Quad Core Embedded Computer, Raspberry Pi 3b New in 2021ECO 200 1-Wire controller of the latest generationwithPlug and Play system (Auto-E-Connect Support) for 1-Wire.No matter which IoT or automation system you are already using or still planning to use, you can combine them with ESERA Station 200.You can combine the following systems with ESERA Station 200: The listed systems are exemplary and depend on the installed application software and hardware extensions. Wired / Cable systems / Bus systems*** (Exemplary) Radio based / Radio systems*** (Exemplary) ESERA 1-Wire Gateway (ASCII and Modbus RTU software interface) EnOcean* KNX* (IP-Symcon, Codesys*****) HomeMatic* digitalSTROM* (IP-Symcon) XBee/Zigbee* LCN* (IP-Symcon) xComfort* DMX lighting technology** (IP-Symcon) Z-Wave* ModBus TCP/RTU**, Slave / Master (IP-Symcon, Codesys*****) Voice control from Amazon (Alexa)*, *** M-Bus* (IP-Symcon) PLC Siemens* / WAGO* / Beckhoff* (IP-Symcon, Codesys*****) PROFINET Controller / Device (Codesys*****) EtherCAT Master (Codesys*****) CANopen Master / Slave (Codesys*****) EtherNet/IP Scanner / Adapter (Codesys*****) * An additional gateway is required for operation. This is not included in the scope of delivery.** The optional RS485 interface is required for operation. The RS485 interface can be ordered together with the Station 200.*** The functions depend on the installed application software. The listed systems are related to the operation with IP-Symcon and Codesys and are to be understood as an example. The scope of functions can be found in the respective application software.**** ESERA sensors and actuators of the Pro series with Auto-E-Connect support are required.***** The offered CODESYS Runtime is intended for testing and teaching purposes. All scripts, software modules and extensions of IP-Symcon can be used. To manage and configure your smart home or smart system, the IP-Symcon management console is available for temptation. After installing the runtime environment, the Raspberry Pi can be programmed as a PLC using the CODESYS Development System.The product is installed into the Linux distribution Raspbian via the CODESYS Development System using the included CODESYS Deploy Tool extension. After each restart of the Raspberry Pi, the runtime system is automatically started.

Variants from €392.31*
From €590.31*

Product number: 19200-3

Available, delivery time 1-5 days, depending on the carrier

ESERA-Station 200 Smart Home IoT
ESERA-Station 200 - expandable, open and future-proof Central control with integrated professional 1-Wire interface for Smart Building, IoT and general automation applicationsTheESERA-Station is the central control unit of your Smart Home and for Internet of Things (IoT). The ESERA station is more like another central controller. It is an open platform, is a combination of an embedded computer and professional ESERA ECO controller. It is an open automation control center built on standards.ESERA station is usable for a variety of software packages, Codesys*****, IP-Symcon, OpenHAB, FHEM, NodeRed and many more, built on a Raspberry Pi 3b.Thefollowing modules are integrated in the ESERA-Station 200:Powerful ARM Quad Core Embedded Computer, Raspberry Pi 3b New in 2021ECO 200 1-Wire controller of the latest generationwithPlug and Play system (Auto-E-Connect Support) for 1-Wire.No matter which IoT or automation system you are already using or still planning to use, you can combine them with ESERA Station 200.You can combine the following systems with ESERA Station 200: The listed systems are exemplary and depend on the installed application software and hardware extensions. Wired / Cable systems / Bus systems*** (Exemplary) Radio based / Radio systems*** (Exemplary) ESERA 1-Wire Gateway (ASCII and Modbus RTU software interface) EnOcean* KNX* (IP-Symcon, Codesys*****) HomeMatic* digitalSTROM* (IP-Symcon) XBee/Zigbee* LCN* (IP-Symcon) xComfort* DMX lighting technology** (IP-Symcon) Z-Wave* ModBus TCP/RTU**, Slave / Master (IP-Symcon, Codesys*****) Voice control from Amazon (Alexa)*, *** M-Bus* (IP-Symcon) PLC Siemens* / WAGO* / Beckhoff* (IP-Symcon, Codesys*****) PROFINET Controller / Device (Codesys*****) EtherCAT Master (Codesys*****) CANopen Master / Slave (Codesys*****) EtherNet/IP Scanner / Adapter (Codesys*****) * An additional gateway is required for operation. This is not included in the scope of delivery.** The optional RS485 interface is required for operation. The RS485 interface can be ordered together with the Station 200.*** The functions depend on the installed application software. The listed systems are related to the operation with IP-Symcon and Codesys and are to be understood as an example. The scope of functions can be found in the respective application software.**** ESERA sensors and actuators of the Pro series with Auto-E-Connect support are required.***** The offered CODESYS Runtime is intended for testing and teaching purposes. All scripts, software modules and extensions of IP-Symcon can be used. To manage and configure your smart home or smart system, the IP-Symcon management console is available for temptation. After installing the runtime environment, the Raspberry Pi can be programmed as a PLC using the CODESYS Development System.The product is installed into the Linux distribution Raspbian via the CODESYS Development System using the included CODESYS Deploy Tool extension. After each restart of the Raspberry Pi, the runtime system is automatically started.

From €392.31*

Product number: 19200-1M

Available, delivery time 1-5 days, depending on the carrier