1-Wire Dual S0 counter module PRO

Product information "1-Wire Dual S0 counter module PRO"

The 1-Wire S0 Meter Pro is designed for energy metering of two independent electricity, water and gas meters or the wind turbine. All S0 energy meters manufactured according to DIN 43864 can be reliably measured. Due to the high-quality electronics of the 1-Wire S0 Meter Pro, energy meters can also be reliably recorded with very high pulse frequencies of up to 300 Hz. The S0 meter values are made available via a 1-Wire bus interface.

In the event of a power failure, the S0 meter values are permanently stored internally for at least 99 years.

Inputs

2 x S0 pulse input (counter) for 2 energy meters or wind sensor

Supply voltage

12V 1-Wire Bus

Power consumption

10mA, both inputs active

S0 Interface

10V and approx. 4mA working level, according to DIN 43864

Counter range / scope

32 bit counter per S0 input

Data preservation / storage Permanent storage of meter values for up to 99 years in the event of a power failure
Data interface 1-Wire Interface, DS2423 command set (GND, Data and 12V)
Operating voltage 12VDC (+10% / -20%)
Power consumption max. 10mA
Operating frequency S0 Input max. 300Hz

Connection

Screw terminals for 1-Wire bus and S0 inputs up to 2,5qmm cable cross section

Dimensions

1HP, 17 x 71x 90mm (WxHxD)

Protection class

III

Note

The counter value can be reset via push button on the front panel

Installation

Designed for control cabinet installation (top hat rail)

Scope of delivery

Finished device and operating instructions

1-Wire Interface: DS2438 instruction set with Plug and Play support (Auto-E-Connect Functions)
1-Wire Plug and Play System, Auto-E-Connect Functions:
  • Automatic Positioning: Advanced Plug And Play system for fully automatic positioning of the sensor / actuator in the ECO Controller
  • Automatic library mapping: The appropriate library is mapped fully automatically for the sensor
  • Classes Assignment: Output OWD sensor class via ECO controller
  • Electronic type plate: output of year of manufacture, software version, software revision, hardware version, OWD position, sensor finder function
  • Pre Configuration: Programming of the desired OWD for the next ECO controller, storage of the OWD number inside the device
Colour: green
Connection type: Screw terminal/s for cable up to 2.5qmm (~ AWG 13) cross-section
Data interface: Industrial 1-Wire Bus (12V, 1-Wire Data und Masse (GND))
Design / Manufacturer: ESERA
Dimensions: 1TE, 17 x 90 x 70mm (LxWxH)
Enclosure: ABS plastic with high percentage of recycled plastic, green (RAL 6020)
Execution: 3 pin connector
Function: Sensoric
Humidity Operation / Storage: 10% to 92% (non-condensing)
Ingress Protection (IP = protection class according to DIN EN 60529), protection class (DIN EN 61140 (VDE 0140-1):
  • IP20
  • Protection class III
Mounting: DIN rail, Top-hat rail or also called mounting rail. According to DIN EN 60715:2018-07, TH 35, formerly TS 35, a mounting rail with top hat profile is
Number of inputs / outputs: 2 - channel input
Plug and Play support , Auto-E-Connect Support: Yes
Power Consumption: 0.1W, 20mA at 5V
Power supply, Supply Voltage: System supply, 12VDC (1-Wire auxiliary voltage)
Protection circuit:
  • Enhanced ESD protection with ±4kV according to IEC 61000-4
  • Reverse polarity protection for voltage supply / power supply
  • Signal line overvoltage protection (1-Wire Protector) provides protection against high voltage faults up to 28VDC
Scope of delivery: Device and Quick Guide, the User Guide (Manual) can be found in the download area as a PDF download.
Temperature range, operation: -5°C to +50°C, standard temperature range
Temperature range, storage: -5°C bis +50°C, Standard temperature range
Version: Professional Version / Professional Serie

2 of 2 reviews

5 out of 5 stars


100%

0%

0%

0%

0%


Leave a review!

Share your experiences with other customers.


Sehr kleiner Bauraum, hochwer...

Sehr kleiner Bauraum, hochwertige Verarbeitung, Bei mir in Verbindung mit dem LAN-Controller im Einsatz. Arbeitet zuverlässig ohne Wartung

funktioniert prima mit IP-Symc...

funktioniert prima mit IP-Symcon, lese damit Windstärke und Wasserverbrauch aus. Die neue Variante ist platzsparender und benötigt keine 12V mehr, prima

Device Documentation Operating instructions, connection diagram, conformity, ...
Info Material Product catalogue, Brochures
Technical Downloads Software & co.
Worth knowing Wikis, entries, tutorials
Electricity meter alternating current
Electronic single-phase alternating current meter Electronic alternating current meter with analogue display for DIN top-hat rail. The electricity meter is designed for quick snap-in mounting on DIN top-hat rails and is therefore ideal for monitoring the consumed KWh in houses, apartments or individual devices in almost all installation cabinets and electrical boxes. The S0 output pulses can be evaluated e.g. by a 1-Wire S0 counter.Top hat rail mounting 18mm / TE (DIN 43880), screw terminal connections for conductors up to 16qmm Voltage range Nominal 230VAC (184V to 265V), 50 - 60Hz Measuring current range 0.02A (type) up to 32A Display 5 digits for kilowatt hours and 2 decimal places Accuracy class 1 Resolution S0 1000 pulses / kWh = 1 pulse / Watt Pulse output S0 Optically decoupled, 5 - 27V and max. 27mA Operating temperature range -20°C to +65°C Power consumption 8VA < 0.4W Dimensions incl. cover caps 118 x 18 x 63mm (LxWxD) Dimensions without cover caps 91 x 18 x 63mm (LxWxD) Scope of delivery Electricity meter Note:When connected, the covers over the terminals must be kept closed.The AC meter is intended for installation in the fuse box and must be installed by a qualified electrician in accordance with the applicable regulations.Technical changes and errors excepted.

From €23.31*

Product number: 96001

Currently not available, please sign up to get notified

Finder 32A Alternating current meter MID
Electronic single-phase alternating current meter MIDFinder 32A alternating current meter MID (7E.13.8.230.00x0) Electronic active current meter from the manufacturer Finder with calibration (MID) with analogue display for 35mm DIN top-hat rail. The electricity meter is designed for quick snap-in mounting on DIN top-hat rails and is therefore ideal for monitoring the consumed electricity in houses, apartments or individual devices in almost all installation cabinets and electrical boxes. Electricity meters according to EN 62053-21 and EN 50470Type approval by PTB (7E.13, 7E.16) (Physikalisch - Technische Bundesanstalt)High resistance to magnetic and mechanical manipulation With SO interface according to DIN 43864 for connection to central tariff devices and for energy management With backstop Sealable with cap as accessory The S0 output pulses can be evaluated e.g. by a 1-Wire S0 counter. The AC meter is intended for installation in the fuse box and must be installed by a qualified electrician in accordance with the applicable regulations. Top hat rail mounting 18mm / TE (DIN 43880), screw terminal connections for conductors up to 16qmm Display: 6 digits for kilowatt hours and 1 decimal placeVoltage range: nominal 230VAC (184V to 265V) Measuring current range: 0,02A (typ) to 32A Limit current LED Display:  2000 Impulse /KW/h Resolution S0: 1000 pulses / KWh = 1 pulse / Watt Pulse output S0: max. 27V and max. 27mA Operating frequency range: 40Hz to 60Hz Operating temperature range: -20°C to + 65°C Dimensions incl. cover caps: 118 x18 x 63mm (LxWxD) Dimensions without cover caps: 91 x 18 x 63mm (LxWxD)Technical changes and errors excepted.

From €69.21*

Product number: 96010

Currently not available, please sign up to get notified

Electricity meter three-phase current
Three-phase meter with analog display for top-hat rail With this three-phase meter you can monitor and measure the electricity consumption of large consumers, a house or an apartment. The S0 output impulses can e.g. be recorded by 1-Wire S0 meters and evaluated by software. The three-phase meter is intended for installation in the fuse box on the house or apartment and must be installed by a qualified electrician in accordance with the applicable regulations. Measuring current range 3 x 10(63) A Voltage range 3 x 230 / 400 VAC, 50 / 60Hz Display Analogue 6+1 (=999999.9 kWh), counter reading is maintained even when no current is applied Design Meter according to IEC62051-11 2003, IEC62053-21 2003 Accuracy class 1 Power consumption >= 10VA (2W) Pulse output S0 Optically decoupled, 5 - 27V and max. 27mA Resolution 800 pulses / kWh = 1 pulse / Watt S0 connection cable max. 20m Display LED LED flashes red when power consumption Operating temperature range -20°C to +45°C Assembly Top hat rail mounting 122mm / TE (DIN 43880) Dimensions incl. cover caps 7 TE, 118 x 122 x 63mm (LxWxD) Dimensions without cover caps 91 x 122 x 63mm (LxWxD) Connection Screw terminals for wires up to 16mm² Scope of delivery Electricity meter and data sheet When connected, the covers over the terminals must be kept closed! Technical changes and errors excepted.

From €63.81*

Product number: 96002

Currently not available, please sign up to get notified