1-Wire 8-fold digital input 10-30V

Relay switch module with 1-Wire and push button interface With this 8-fold switching module 8 DC or AC consumers can be switched via 1-Wire interface, via 8 external push buttons or the buttons on the module surface. This can be used to operate lighting, radiator valves or sockets, for example. The module is designed for a load capacity of 8A per channel and a total of 10A continuous current.

High Power 8-fold switch module for 1-Wire bus system with push-button interface With this 8-fold switching module 8 DC or AC consumers can be switched via 1-Wire interface, via 8 external push buttons or the buttons on the module surface. This can be used to operate lighting, radiator valves or sockets, for example. The module is designed for a load capacity of 10A per channel (16A for 3 seconds) continuous current. Each channel has a separate current input. This allows you to switch 8 independent circuits with the maximum power of a 10A circuit breaker. The 8 external button inputs and the status of the relay outputs are displayed separately via the 1-wire interface. In addition, the status of the relay outputs is displayed via the 1-Wire interface, regardless of whether the relay output was switched via external button, internal menu or 1-Wire interface. Output 8 x relay normally open contacts (NO), separate current inputs per channel Switching voltage Direct or alternating voltage up to 230V Switching current 10A per output Continuous current, 16A for 3 seconds Interfaces 1. bus interface (1-wire bus) 2. push-button interface (binary input 8 x 10-30VDC, normally open contact) 3. manual operation via operating menu on the module top side Supply voltage 12V Only Interface 1-Wire interface, commands for DS2408 Power consumption min. 13mA (0.156W), max. 270mA (3.24W, all outputs active) Connection Screw terminals for 1-Wire bus, push button interface and relay output up to 2.5qmm cable cross section Dimensions 100 x 71 x 90mm (WxHxD) Accessories Back-up fuse per channel Scope of delivery Finished device, operating instructions

1-Wire Hub III DC, central power supply and distribution for the 1-Wire network with 24VDC input voltage. The 1-Wire Hub III DC is the central module for building a 1-Wire network. The 1-Wire Hub III DC supplies the 1-Wire network with 5V and 12V voltage and distributes the 1-Wire data line. 1-Wire Hub III DC can be ideally combined with a 1-Wire bus coupler (USB, Ethernet or serial) or 1-Wire controller. The input voltage of the 1-Wire Hub III DC is nominally 24VDC (18-36VDC) and is therefore especially suited for system environments with DC voltage supply, such as PLC controls. Equipment / Function: Central power supply of the 1-Wire network 1-Wire distribution for several bus sections LED display for power and 1-Wire activity Measurement function for the output voltages (voltage and current measurement for the 5V and 12V output)Note: The device has no repeater function for the 1-Wire data signal, which means that the device does not increase the possible network size.Note: The device has no repeater function for the 1-Wire data signal, which means that the device does not increase the possible network size.

With the ESI 400 4 Channel Switch Input Module, push buttons, switches or reed contacts can be (magnetic switch) can be interrogated. For example, the status of doors, windows, roof windows, fire dampers or a garage door can be recorded. A reed switch is only to be attached at a suitable place and connected to the ESI 400 module. The Status LED flashes when the status of one of the inputs has changed. Even short switching pulses, e.g. from buttons, are detected by the ESI 400 4-Channel Switch Input Module and stored until the next readout cycle.The ESI 400 module can be connected directly to switches or buttons. No external voltage is required for the switches. The ESI 400 module can be supplied with 5V - 12V operating voltage. Function 4 digital inputs for querying push-button or switch No external voltage for buttons or switches necessary Short keystrokes are also stored until the next readout cycle Digital inputs with filters for "calmed" buttons / switch queries Very small housing, intended for installation in flush boxes number of inputs 4 digital inputs for push-button or switch pulse duration at least 40ms Operating voltage Pushbutton / switch approx. 5V DC voltage with approx. 1mA current inputs are connected to the ground potential of the operating voltage (bus interface) Connection length inputs Cable length per input max. 20m Bus interface 1-Wire bus, interface with DS2408 command setThe data line operates with typ. 5V voltage Operating voltage 5 - 12V DC voltage (+/-10%) with max. 20mA current consumption Display LED display for power and status change of the inputs Connection Screw terminals 0,2 - 1,5qmm Cable cross section Dimensions 43 x 43 x 25mm (LxWxH), optimized for installation in flush boxes Protection class / IP class Protection class III, IP20 Scope of delivery Device and operating instructions in German, English Manual via download