1-Wire Dual switching module Pro 230V 10/16A with push-button interface

Product information "1-Wire Dual switching module Pro 230V 10/16A with push-button interface"

1-Wire Dual Switching Module Pro 10/16A Relay with Push Button Interface

Application

The 1-Wire Dual switching module can switch all types of DC or AC loads with up to 16/10A current. This allows all types of loads to be switched.
The module is also ideally suited for lighting control in living areas, as the module is equipped with two push-button inputs in addition to the 1-wire interface. No external voltage is required for the button inputs. You can use it to switch the light on or off, for example, either by push-button or 1-Wire command. The advantage here is that the basic function, On-Off, is always given by push button. Automatic functions such as scenes or "Central Off" are added via the 1-Wire interface. The current relay and button status is reported via a 1-wire interface.

Features

  • The 1-Wire Dual Switching Module has two high power switching relays for switching two DC or AC loads.
  • You will always receive the current relay status via a 1-Wire interface, regardless of whether it is switched by a 1-Wire command, manual operation or an external pushbutton.
  • You also receive the status of the digital input (button interface) via the 1-Wire interface.
1-Wire Interface: DS2408 instruction set with Plug and Play support (Auto-E-Connect Functions)
1-Wire Plug and Play System, Auto-E-Connect Functions:
  • Automatic Positioning: Advanced Plug And Play system for fully automatic positioning of the sensor / actuator in the ECO Controller
  • Automatic library mapping: The appropriate library is mapped fully automatically for the sensor
  • Classes Assignment: Output OWD sensor class via ECO controller
  • Electronic type plate: output of year of manufacture, software version, software revision, hardware version, OWD position, sensor finder function
  • Pre Configuration: Programming of the desired OWD for the next ECO controller, storage of the OWD number inside the device
Colour: green
Connection type: Screw terminal/s for cable up to 2.5qmm (~ AWG 13) cross-section
Data interface: Industrial 1-Wire Bus (12V, 1-Wire Data und Masse (GND))
Design / Manufacturer: ESERA
Dimensions: 2TE, 32 x 90 x 70mm (LxWxH)
Enclosure: ABS plastic with high percentage of recycled plastic, green (RAL 6020)
Execution:
  • Pushbutton interface (binary input 10-30VDC, normally open contact) to control the outputs
  • Rollladen oder Markisenbetrieb: Steuereingänge für Aufwärts, Stopp, Abwärts. Raffstore oder Jalousien: Taster, kurz für Kippbewegung, Taster, lang für Aufwärts, Stopp, Abwärts.
Function: Digital output
Humidity Operation / Storage: 10% to 92% (non-condensing)
Ingress Protection (IP = protection class according to DIN EN 60529), protection class (DIN EN 61140 (VDE 0140-1):
  • IP20
  • Protection class II
Mounting: DIN rail, Top-hat rail or also called mounting rail. According to DIN EN 60715:2018-07, TH 35, formerly TS 35, a mounting rail with top hat profile is
Note: In the case of capacitive or inductive loads, appropriate additional circuitry, such as spark suppression capacitors, must be provided. Minimum load 10mA per output The max. current and power are reduced for non-resistive loads.
Number of inputs / outputs:
  • 2 x push button interface (binary input/pulse input 10-30VDC) to control the outputs
  • 2 x relay output, changeover contacts (NO/NC), separate current inputs per channel
  • Relay output (COM, NO)
Plug and Play support , Auto-E-Connect Support: Yes
Power Consumption: 0.048W, (min. 6mA), 0.84W (max. 70mA) all outputs active at 12V
Power supply, Supply Voltage: System supply, 12VDC (1-Wire auxiliary voltage)
Protection circuit:
  • Enhanced ESD protection with ±4kV according to IEC 61000-4
  • Reverse polarity protection for voltage supply / power supply
  • Signal line overvoltage protection (1-Wire Protector) provides protection against high voltage faults up to 28VDC
Scope of delivery: Device and Quick Guide, the User Guide (Manual) can be found in the download area as a PDF download.
Temperature range, operation: -5°C to +50°C, standard temperature range
Temperature range, storage: -5°C bis +50°C, Standard temperature range
Version: Professional Version / Professional Serie

0 of 0 reviews

Leave a review!

Share your experiences with other customers.


Device Documentation Operating instructions, connection diagram, conformity, ...
Info Material Product catalogue, Brochures
Technical Downloads Software & co.
Worth knowing Wikis, entries, tutorials
1-Wire Hub III DC, central power supply
1-Wire Hub III DC, central power supply and distribution for the 1-Wire network with 24VDC input voltage. The 1-Wire Hub III DC is the central module for building a 1-Wire network. The 1-Wire Hub III DC supplies the 1-Wire network with 5V and 12V voltage and distributes the 1-Wire data line. 1-Wire Hub III DC can be ideally combined with a 1-Wire bus coupler (USB, Ethernet or serial) or 1-Wire controller. The input voltage of the 1-Wire Hub III DC is nominally 24VDC (18-36VDC) and is therefore especially suited for system environments with DC voltage supply, such as PLC controls. Equipment / Function: Central power supply of the 1-Wire network 1-Wire distribution for several bus sections LED display for power and 1-Wire activity Measurement function for the output voltages (voltage and current measurement for the 5V and 12V output)Note: The device has no repeater function for the 1-Wire data signal, which means that the device does not increase the possible network size.Note: The device has no repeater function for the 1-Wire data signal, which means that the device does not increase the possible network size.

From €70.11*

Product number: 11322

Available, delivery time 1-5 days, depending on the carrier

1-Wire distributor 4 star wiring with Push In terminals
1-Wire distributor for cabling of 1-Wire sensors in star or tree topology 6 outputs on push-in terminals* plus one RJ45 modular jackDistribution module for easy cabling in linear bus topology of 1-Wire sensors and actuators. Designed for CAT5, CAT6 cabling, telephone cables (2 x 2x 0.8qmm) or EIB cables. This allows a fast and cost sensitive cabling. By using Push In terminals you do not need a screwdriver for mounting. Also the times of loosening screws are over. You can connect several 1-Wire Distributors 3 to other 1-Wire Distributors quickly and easily using network patch cables.The distributor complements the existing 1-Wire cabling system based on CAT patch cables.*Push In terminals are screwless terminal connections.

From €32.31*

Product number: 11142

Available, delivery time 1-5 days, depending on the carrier

1-Wire Analog Output PRO 0-10V Isolated
With the 1-Wire Analog Output Pro, a DC voltage in the range of 0-10V with a resolution of 8 bits can be easily output. The 1-Wire analog output module can be used to control a heating mixer, a dimmer or other power units, for example. The analog output is galvanically isolated from the 1-wire bus and the power supply. The insulation prevents ground loops or effects due to potential differences. Analog output 0-10 VDC, max. 20 mA Resolution 8 bits Connection Screw terminals for 1-Wire bus and input voltage (up to 2.5qmm) Interface 1-Wire Bus (GND, Data, +12V) Data interface 1-Wire Interface, DS2408 Command Set Operating voltage 12VDC (+10% / -20%) Power consumption max. 30mA Dimensions 1HP, 17 x 71x 90mm (WxHxD) Isolation Analog output electrically isolated against 1-Wire interface Assembly Designed for control cabinet installation (top hat rail) Protection class III Scope of delivery Finished device and operating instructions

From €59.31*

Product number: 11208

Available, delivery time 1-5 days, depending on the carrier

1-Wire 8-fold switch module 230V 8A with button inputs
Relay switch module with 1-Wire and push button interface With this 8-fold switching module 8 DC or AC consumers can be switched via 1-Wire interface, via 8 external push buttons or the buttons on the module surface. This can be used to operate lighting, radiator valves or sockets, for example. The module is designed for a load capacity of 8A per channel and a total of 10A continuous current.

From €127.71*

Product number: 11220

Available, delivery time 1-5 days, depending on the carrier

1-Wire 8-fold switch module 230V 16A with button inputs V2
High Power 8-fold switch module for 1-Wire bus system with push-button interface With this 8-fold switching module 8 DC or AC consumers can be switched via 1-Wire interface, via 8 external push buttons or the buttons on the module surface. This can be used to operate lighting, radiator valves or sockets, for example. The module is designed for a load capacity of 10A per channel (16A for 3 seconds) continuous current. Each channel has a separate current input. This allows you to switch 8 independent circuits with the maximum power of a 10A circuit breaker. The 8 external button inputs and the status of the relay outputs are displayed separately via the 1-wire interface. In addition, the status of the relay outputs is displayed via the 1-Wire interface, regardless of whether the relay output was switched via external button, internal menu or 1-Wire interface. Output 8 x relay normally open contacts (NO), separate current inputs per channel Switching voltage Direct or alternating voltage up to 230V Switching current 10A per output Continuous current, 16A for 3 seconds Interfaces 1. bus interface (1-wire bus) 2. push-button interface (binary input 8 x 10-30VDC, normally open contact) 3. manual operation via operating menu on the module top side Supply voltage 12V Only Interface 1-Wire interface, commands for DS2408 Power consumption min. 13mA (0.156W), max. 270mA (3.24W, all outputs active) Connection Screw terminals for 1-Wire bus, push button interface and relay output up to 2.5qmm cable cross section Dimensions 100 x 71 x 90mm (WxHxD) Accessories Back-up fuse per channel Scope of delivery Finished device, operating instructions

From €143.91*

Product number: 11228

Available, delivery time 1-5 days, depending on the carrier

1-Wire Shutter Pro shutter control V4
Shutter control / Shutter Pro for 1-Wire bus and push button interface With the 1-Wire Shutter Pro module you can easily control a roller shutter motor, external blinds or awnings manually or automatically via the 1-Wire network. Thus a central and convenient control as well as local decentralized control is possible. The output of the 1-Wire Shutter Pro is switched by relays, which are electrically interlocked with each other. This can result in an up and down command for the tubular motor at the same time. In addition, a safety shutdown is provided, which automatically switches off the motor after 120 seconds. New, a runtime can now be transferred via software (1-Wire interface) in addition to an Up or Down command. Travel times of 250ms, 500ms and 750ms for tilting movements and 1-60 seconds for normal running operation can now be transferred. New: The status of the output (relay status) and the button inputs is output via the 1-Wire interface.With additional isolating relays, shutter groups can be controlled via a module. product details: Convenient manual operation via push-buttons for up and down, which can be installed in the window area or next to a room door, for example. A harmless DC voltage of 10-30V is used to operate the external pushbuttons. Automatic operation via 1-Wire commands via the data interface. An integrated safety circuit automatically switches off the roller shutter motor after 120 seconds. This provides additional protection for the motor in case of a defective limit position switch. Note: Module is only intended for roller shutter motors with integrated limit switches. Control system 1-Wire interface (DS2408 command set) Manual operation by push button on top of the module Digital / binary input for external push buttons (manual operation) Up / Down times per 1-Wire interface 250ms, 500ms and 750ms for tilting movements of laminations and external blinds Shading 1 - 60 seconds in 1 second steps for up and down movement 120 seconds per automatic safety stop (no time input required) Functions Module function switchable for roller shutters or lamella or external blinds Advertisements LED display Up / Down Digital / binary input for external push buttons (manual operation) 10-30VDC max. 10mA, electrically isolated Switching power/current 1150VA, 5A continuous current (resistive load) Operating voltage 5 - 230V direct or alternating voltage Connection Screw terminals for cable cross sections up to 2,5qmm Supply voltage +12VDC, max. 20mA Interface 1-Wire interface, three-wire system with ground/GND, Data and +12V 1-Wire interface DS2408 command set Dimensions 2HP, 32 x 71x 90mm (WxHxD) Connection Screw terminals Scope of delivery Finished device, operating instructions Controlled by 1-Wire controller 1 / 1-Wire gateway by command "Up" and "Down" with time function. For details, please refer to the programming manual for the 1-Wire controller / 1-Wire gateway / Station-200. convenient software modules are available for free download for integration into IP-Symcon, 1-Wire controller and ESERA Station 200. For details please refer to the category "Compatible controllers / IP-Symcon".

From €53.91*

Product number: 11231

Available, delivery time 1-5 days, depending on the carrier